Flexispot Standing Desk Evaluation …Flexispot Desk Not Going Down…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are very little, here are a couple of features that I wasn’t always a big fan of:
The bundle that the desk was available in was heavy, so bringing it inside was a group effort, however this is just a repercussion of how sturdy the Flexispot is.
The convenient cable tray was a bit confusing to set up. In the end, you eventually slip it under screws, which wasn’t very clear from the instructions.
You will need to purchase an anti-fatigue mat to stay comfy, but this is an excellent idea for any standing desks, so I can’t fault Flexispot for that.
When it showed up and I saw how heavy it was, I was both excited (considering that this implied it was going to be tough) and also a little hesitant (because all of us know just how much of a difficulty putting together furnishings can be).
The good news is, with the help of an educational YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only problem I have with assembly was the cable tray, which I discovered wasn’t discussed well in the instructions.
When put together, I like the smooth look of this desk. I’m positive any of the many varied finishes that it comes in would look terrific in any workplace, and the adjustable width makes it easy to fit it in even the tiniest of office.
The peaceful operation and height memory settings make it easy, effective, and quiet to switch in between sitting and standing as often times as you want throughout the day.
This desk is durable. It can hold up to 335 pounds even while in operation, so if you have a large home computer (or wish to rest on it for some reason) it has you covered. It will also evenly disperse weight no matter how out of balance the weight you place on it is, it won’t wiggle or wobble.
in that video is quite kitted out as the desk we’re taking a look at today is quite fundamental I attempted to get as close to that as I could on uplifts website with equivalent setups the flexi area desk we’re taking a look at today will run you about four hundred and ten dollars versus six hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift design is actually 5 inches longer however you can do a lot with 5 inches boom yes now for openness flexi area did send this desk out for review but as you ought to know by now does not impact my evaluation in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering up until completion of April at the earliest the desktop is an inch thick however it’s this basic laminate as you can potentially get doing not have even any cable television grommets for go through the outside carton
for the desktop was not harmed in any way which is utterly unusual since I could shoot a 30-second b-roll montage of simply the damage and flaws on this desktop scuffed scraped pitted just incredibly rough male if I had acquired this I ‘d have been on the phone with customer support immediately they did likewise handled to miss out on drilling the pilot holes where you can attach the control box to the desktop a lot of needing to do that myself without unintentionally drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was in fact pretty straightforward the entire thing came together in about 45 minutes and despite the fact that there’s cables running to it from each part to support motorized function strangely absolutely where any sort of cable management materials whatsoever the frame on this unit is a single motor double stage style versus the dual motor three-stage design that comes standard with the uplift desk this can be updated too to both the dual phase double motor and a three-stage double motor which pushes the cost of the desk up
an additional 70 dollars the frame is created for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from just under 28 inches to just over forty 7 point six inches so a max I ‘d it is more than high enough even for me and I remain at 6 foot for this design does come standard with the control board that allows for up-and-down movement plus 3 memory spots with an LED readout to inform you the desk height the single motor design uses this drive shaft assembly which needs to be adjusted as the width of the desk is adjusted the motor operation itself while it might be slow is very peaceful as in barely audible this outside a cost would be the one advantage I would give this system over the uplift desk and I wish to be careful here since this isn’t a hit piece this desk is 240 dollars more affordable than the comparable uplift design over 35% more affordable even if you upgrade this flexi spot test to the dual motor three-stage design it still is available in a hundred and seventy dollars less expensive than the uplift however more affordable doesn’t suggest low-cost this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is solid even if max height I’ll definitely provide it that but the lateral stability of this desk the horizontal movement at this rate point it’s inappropriate it’s add fuel to the fire here they include a little security baffle this little steel piece that installs to the frame and covers a part of this rotating driveshaft when
this desk sees any lateral motion at all the drive shaft strikes this baffle and the sound is definitely shocking to leading things off I decided to include rolling casters to this desk this was a $30 upgrade and two of those four casters arrived damaged also my plan for this desk at this moment is to lose the desk top and included all together and replace it with a white laminate lemon table from Ikea and utilize it as an adjustable photo table which you can’t do this frame will accommodate desktops up to 63 inches wide and 31 and a half inches deep so this will roll around the studio make it easier to film items without needing to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is an investment in quality office furnishings that will last you this at finest feels like a cheaper replica of that it simply does not feel quality and the distinction between this desk and my primary desk is night and day do feel free to check out their site also which likewise feels strangely similar to one of their competitors there’s a wealth of devices you can get for the flexi area desk approximately and including a foot massager and even a stationary exercise bike and I could spend another 10 minutes of our valuable time covering various options and devices I might however I think I’m better that they just sent out a basic desk due to the fact that as a basic desk I’m not a fan of the quality assurance at this rate point and I do not think slapping on a bunch of extras is the move when the core item isn’t what it ought to be they do use a 30-day trial if you’re just morbidly curious and they service warranty their desks for three years very desk is five years and uplift desk is seven years if you are Flexispot Desk Not Going Down
in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in terms of gaming and efficiency but I would invest the additional money it’s gon na require to get into a higher end producer like uplift desk or extremely desk and I have not personally used extremely desk products so I can’t speak on it but their credibility is very good big thanks to flexi spot for sending this out for review sadly I can not advise this system and for the record I’m a hundred percent sure they would have happily replaced the parts that I had a concern with seeing as how both the desktop and the casters showed up harmed however from a customer viewpoint you ‘d probably be truly delighted to get this in